This article is rated Stub-class on Wikipedia's
content assessment scale. It is of interest to the following WikiProjects: | |||||||||||
|
I wonder about the sentence "The physical layer for TMDS is current mode logic (CML), DC coupled and terminated to 3.3 Volts.", could the second part be clarified? CML has a link with further information, but though I am interested in electronics and (almost) obsessed with computers I am not sure how to interpret DC coupled or terminated to 3.3 Volts.
(So far I imagine that it could mean that there are no decoupling capacitors, meaning that the actual DC level will be shared/transferred over the physical medium, and maybe that both sides are supposed to attempt to keep each line at a 3.3V DC bias/offset.)
I find no useful or unambiguous reference for DC coupled on Wikipedia, and a clarification in this context would at least be helpful for me. --
Johan Adler (
talk)
09:11, 14 August 2012 (UTC)
The article states "The physical layer for TMDS is current mode logic (CML)..." I would like to see citation to support and provide understanding for this assertion. The referenced Digital Visual Interface specification document states in section 4.1, page 33, "T.M.D.S. technology uses current drive to develop the low voltage differential signal at the receiver side of the DC-coupled transmission line." It does not use the term "Current Mode Logic." Furthermore, the diagram in Figure 4-1 shows the link with pull-ups only at the Receiver side; the transmitter can pull down each conductor through a current sink to ground. This diagram does not show pull-ups on the transmitter side.
Maxim AN291, ( http://pdfserv.maxim-ic.com/en/an/AN291.pdf) referenced in the Current Mode Logic article, shows in Figure 3 on page 3, a CML output structure that includes 50 ohm pull-ups on both the output (transmitter) and input (receiver.) So are there different drive types of CML, and can it include the variety shown in the DVI document, with no pull-ups on the transmitter side? If so, I would like to see a supporting citation. Or perhaps it is not correct to say that the TMDS physical layer is CML, and the DVI document is correct in using the term "current drive" to indicate something that may be similar to CML, but not the same.
Also note that the article on Current Mode Logic has the same issue. Agrjlc ( talk) 20:55, 27 June 2013 (UTC)
Which is the voltage swing of the signals? Is this variant oder constant / well defined for HDMI? The LVDS specification ist not clear. 213.61.254.68 ( talk) 14:12, 26 September 2019 (UTC)
This article is rated Stub-class on Wikipedia's
content assessment scale. It is of interest to the following WikiProjects: | |||||||||||
|
I wonder about the sentence "The physical layer for TMDS is current mode logic (CML), DC coupled and terminated to 3.3 Volts.", could the second part be clarified? CML has a link with further information, but though I am interested in electronics and (almost) obsessed with computers I am not sure how to interpret DC coupled or terminated to 3.3 Volts.
(So far I imagine that it could mean that there are no decoupling capacitors, meaning that the actual DC level will be shared/transferred over the physical medium, and maybe that both sides are supposed to attempt to keep each line at a 3.3V DC bias/offset.)
I find no useful or unambiguous reference for DC coupled on Wikipedia, and a clarification in this context would at least be helpful for me. --
Johan Adler (
talk)
09:11, 14 August 2012 (UTC)
The article states "The physical layer for TMDS is current mode logic (CML)..." I would like to see citation to support and provide understanding for this assertion. The referenced Digital Visual Interface specification document states in section 4.1, page 33, "T.M.D.S. technology uses current drive to develop the low voltage differential signal at the receiver side of the DC-coupled transmission line." It does not use the term "Current Mode Logic." Furthermore, the diagram in Figure 4-1 shows the link with pull-ups only at the Receiver side; the transmitter can pull down each conductor through a current sink to ground. This diagram does not show pull-ups on the transmitter side.
Maxim AN291, ( http://pdfserv.maxim-ic.com/en/an/AN291.pdf) referenced in the Current Mode Logic article, shows in Figure 3 on page 3, a CML output structure that includes 50 ohm pull-ups on both the output (transmitter) and input (receiver.) So are there different drive types of CML, and can it include the variety shown in the DVI document, with no pull-ups on the transmitter side? If so, I would like to see a supporting citation. Or perhaps it is not correct to say that the TMDS physical layer is CML, and the DVI document is correct in using the term "current drive" to indicate something that may be similar to CML, but not the same.
Also note that the article on Current Mode Logic has the same issue. Agrjlc ( talk) 20:55, 27 June 2013 (UTC)
Which is the voltage swing of the signals? Is this variant oder constant / well defined for HDMI? The LVDS specification ist not clear. 213.61.254.68 ( talk) 14:12, 26 September 2019 (UTC)