![]() | This article is rated Start-class on Wikipedia's
content assessment scale. It is of interest to the following WikiProjects: | ||||||||||
|
The Mini article is in the Wikipedia:Peer review process - perhaps heading towards Featured Article status. I would greatly appreciate experts on A-series engines taking a look at it. (If you find a problem, please either fix it or post your concerns on the Talk:Mini page. TIA SteveBaker 20:50, 24 February 2006 (UTC)
SPi should be under a new heading like Twin point injection.
Describing the new/developed engines, is it too much to ask how they differed, more than just a pow/torque rating? Trekphiler 02:40, 4 October 2007 (UTC)
Is there any further information available?? ANY sources to name? Where does the information "22HP" come from? Strassenbelag 22:20, 30 November 2007 (UTC)
Perhaps some mention should be made of the fact that all the A series engines were OHV - this engine appeared around the time the industry was moving away from side valve to OHV. As an example, the first engine in the Morris Minor was a side valve type, and Ford used side valves in their smaller British cars until the end of the 1950s. Soarhead77 ( talk) 18:36, 16 June 2008 (UTC)
I think there should be a section on the factory race engines, initially produced for Formula Junior, but also used in Sebring Sprites.
From FJ site http://www.formulajunior.com/Car%20Marques/08%20Cars/Cooper/Cooper.html there would appear to be four successive XSP dry sump inline engines built by the factory or Morris Engines. Not sure if Sprite versions dry or wet sump.
For 1960 there was a 948 bored out to 64.4mm x 76.2mm stroke for 994cc (FJ site) 995cc (most often quoted online), but actually calcs as 993cc! Twin SUs
For 1961, same 993, but with twin-choke Weber
For 1962, bored out to 67.6 x 76.2 for quoted 1095 (1094 calc), twin-choke Weber. Not sure if still based on 948 block.
For 1963, bored out to 71.5, with stroke of 68.2 (probably 68.28 as in Mini)gives quoted 1098 (1097 calc) This obviously the inline version of 1071 Cooper S engine, bored close to 1100 FJ limit. For use in Mini, it would seem BMC allowed for a rebore whilst staying within 1100 class racing. Not sure if special block. Which came first -- 1097 inline or 1071 transverse?
Lots still to find out -- feedback welcome — Preceding unsigned comment added by Timetack ( talk • contribs) 20:24, 9 November 2015 (UTC)
Hello fellow Wikipedians,
I have just modified one external link on BMC A-Series engine. Please take a moment to review my edit. If you have any questions, or need the bot to ignore the links, or the page altogether, please visit this simple FaQ for additional information. I made the following changes:
When you have finished reviewing my changes, you may follow the instructions on the template below to fix any issues with the URLs.
This message was posted before February 2018.
After February 2018, "External links modified" talk page sections are no longer generated or monitored by InternetArchiveBot. No special action is required regarding these talk page notices, other than
regular verification using the archive tool instructions below. Editors
have permission to delete these "External links modified" talk page sections if they want to de-clutter talk pages, but see the
RfC before doing mass systematic removals. This message is updated dynamically through the template {{
source check}}
(last update: 5 June 2024).
Cheers.— InternetArchiveBot ( Report bug) 05:33, 13 July 2017 (UTC)
With the introduction of the 4 speed AP automatic transmission fitted to Minis and 1100's from 1966, the engine power was increased to offset power lost in the torque converter. The 848cc was increased from 34bhp to 39bhp, the 998 from 38bhp to 44bhp and the 1098 from 48bhp to 56bhp (the figure for the 1098 is actually in the BL workshop manual in the section on General Data - page general data 9. The torque is also quoted as 61ftlb at 2000rpm). These increases in power were achieved by higher compression, larger inlet valves and an HS4 carb. There was no increase in power for the Austin/Morris 1300 which remained at 60bhp (though I have (somewhere !) a BL brochure for a Wolseley 1300 showing an engine bay picture of an automatic with twin carbs - so presumably 65bhp. I owned a Wolseley 1300 auto (TAR244J) but it had a single carb 60bhp engine fitted as standard).
The MG1100 is generally quoted as 55bhp which is correct up to 1966, but it then benefitted from improvements to the 8.9:1 head fitted to the automatic with even larger inlet valves and the power was increased to 57bhp at 5500rpm.
Tony Erwood. — Preceding unsigned comment added by 37.235.41.82 ( talk) 21:59, 29 December 2017 (UTC)
Should the detailed information about the Nissan development of this engine be in this article? A reference to the licensing and a wikilink to the Nissan version page should be enough. — Preceding unsigned comment added by 84.51.155.34 ( talk) 18:06, 12 September 2020 (UTC)
I'm a bit surprised this article has barely any mention of the fact this engine typically has a sump-mounted gearbox in FWD applications - often considered a key feature of this engine, and something that probably could do with being described in at least some detail considering the engine's long history going well into the era when the gearbox-on-end transverse layout became the de facto standard. There's also no mention of the automatic gearboxes besides the description of one photo. It certainly deserves more of a mention than the huge paragraph about Nissan engines... Zilog Jones ( talk) 10:50, 28 August 2021 (UTC)
See [1]
In reference to
Andy Dingley (
talk)
08:38, 1 September 2023 (UTC)
In the Engine family list section, it states “ All A-series engines up until mid-1970 were painted in British Standard (381c) 223 "Middle Bronze Green".” and gives a vague reference as “Austin Morris (BL) internal documents archives.” I’d be interested to see what this source actually is, as it is not correct; for example Sprite and Midget engines were painted a pale metallic green between late 1967 and late 1971 (Horler, Terry (1994). Original Sprite & Midget. Bay View Books. pp. 100-101 ISBN 1 870979 45 1 Emmajnation ( talk) 16:24, 12 October 2023 (UTC)
![]() | This article is rated Start-class on Wikipedia's
content assessment scale. It is of interest to the following WikiProjects: | ||||||||||
|
The Mini article is in the Wikipedia:Peer review process - perhaps heading towards Featured Article status. I would greatly appreciate experts on A-series engines taking a look at it. (If you find a problem, please either fix it or post your concerns on the Talk:Mini page. TIA SteveBaker 20:50, 24 February 2006 (UTC)
SPi should be under a new heading like Twin point injection.
Describing the new/developed engines, is it too much to ask how they differed, more than just a pow/torque rating? Trekphiler 02:40, 4 October 2007 (UTC)
Is there any further information available?? ANY sources to name? Where does the information "22HP" come from? Strassenbelag 22:20, 30 November 2007 (UTC)
Perhaps some mention should be made of the fact that all the A series engines were OHV - this engine appeared around the time the industry was moving away from side valve to OHV. As an example, the first engine in the Morris Minor was a side valve type, and Ford used side valves in their smaller British cars until the end of the 1950s. Soarhead77 ( talk) 18:36, 16 June 2008 (UTC)
I think there should be a section on the factory race engines, initially produced for Formula Junior, but also used in Sebring Sprites.
From FJ site http://www.formulajunior.com/Car%20Marques/08%20Cars/Cooper/Cooper.html there would appear to be four successive XSP dry sump inline engines built by the factory or Morris Engines. Not sure if Sprite versions dry or wet sump.
For 1960 there was a 948 bored out to 64.4mm x 76.2mm stroke for 994cc (FJ site) 995cc (most often quoted online), but actually calcs as 993cc! Twin SUs
For 1961, same 993, but with twin-choke Weber
For 1962, bored out to 67.6 x 76.2 for quoted 1095 (1094 calc), twin-choke Weber. Not sure if still based on 948 block.
For 1963, bored out to 71.5, with stroke of 68.2 (probably 68.28 as in Mini)gives quoted 1098 (1097 calc) This obviously the inline version of 1071 Cooper S engine, bored close to 1100 FJ limit. For use in Mini, it would seem BMC allowed for a rebore whilst staying within 1100 class racing. Not sure if special block. Which came first -- 1097 inline or 1071 transverse?
Lots still to find out -- feedback welcome — Preceding unsigned comment added by Timetack ( talk • contribs) 20:24, 9 November 2015 (UTC)
Hello fellow Wikipedians,
I have just modified one external link on BMC A-Series engine. Please take a moment to review my edit. If you have any questions, or need the bot to ignore the links, or the page altogether, please visit this simple FaQ for additional information. I made the following changes:
When you have finished reviewing my changes, you may follow the instructions on the template below to fix any issues with the URLs.
This message was posted before February 2018.
After February 2018, "External links modified" talk page sections are no longer generated or monitored by InternetArchiveBot. No special action is required regarding these talk page notices, other than
regular verification using the archive tool instructions below. Editors
have permission to delete these "External links modified" talk page sections if they want to de-clutter talk pages, but see the
RfC before doing mass systematic removals. This message is updated dynamically through the template {{
source check}}
(last update: 5 June 2024).
Cheers.— InternetArchiveBot ( Report bug) 05:33, 13 July 2017 (UTC)
With the introduction of the 4 speed AP automatic transmission fitted to Minis and 1100's from 1966, the engine power was increased to offset power lost in the torque converter. The 848cc was increased from 34bhp to 39bhp, the 998 from 38bhp to 44bhp and the 1098 from 48bhp to 56bhp (the figure for the 1098 is actually in the BL workshop manual in the section on General Data - page general data 9. The torque is also quoted as 61ftlb at 2000rpm). These increases in power were achieved by higher compression, larger inlet valves and an HS4 carb. There was no increase in power for the Austin/Morris 1300 which remained at 60bhp (though I have (somewhere !) a BL brochure for a Wolseley 1300 showing an engine bay picture of an automatic with twin carbs - so presumably 65bhp. I owned a Wolseley 1300 auto (TAR244J) but it had a single carb 60bhp engine fitted as standard).
The MG1100 is generally quoted as 55bhp which is correct up to 1966, but it then benefitted from improvements to the 8.9:1 head fitted to the automatic with even larger inlet valves and the power was increased to 57bhp at 5500rpm.
Tony Erwood. — Preceding unsigned comment added by 37.235.41.82 ( talk) 21:59, 29 December 2017 (UTC)
Should the detailed information about the Nissan development of this engine be in this article? A reference to the licensing and a wikilink to the Nissan version page should be enough. — Preceding unsigned comment added by 84.51.155.34 ( talk) 18:06, 12 September 2020 (UTC)
I'm a bit surprised this article has barely any mention of the fact this engine typically has a sump-mounted gearbox in FWD applications - often considered a key feature of this engine, and something that probably could do with being described in at least some detail considering the engine's long history going well into the era when the gearbox-on-end transverse layout became the de facto standard. There's also no mention of the automatic gearboxes besides the description of one photo. It certainly deserves more of a mention than the huge paragraph about Nissan engines... Zilog Jones ( talk) 10:50, 28 August 2021 (UTC)
See [1]
In reference to
Andy Dingley (
talk)
08:38, 1 September 2023 (UTC)
In the Engine family list section, it states “ All A-series engines up until mid-1970 were painted in British Standard (381c) 223 "Middle Bronze Green".” and gives a vague reference as “Austin Morris (BL) internal documents archives.” I’d be interested to see what this source actually is, as it is not correct; for example Sprite and Midget engines were painted a pale metallic green between late 1967 and late 1971 (Horler, Terry (1994). Original Sprite & Midget. Bay View Books. pp. 100-101 ISBN 1 870979 45 1 Emmajnation ( talk) 16:24, 12 October 2023 (UTC)