In electronics, TO-5 is a designation for a standardized metal semiconductor package used for transistors and some integrated circuits. The TO element stands for "transistor outline" and refers to a series of technical drawings produced by JEDEC. [1] The first commercial silicon transistors, the 2N696 and 2N697 from Fairchild Semiconductor, came in a TO-5 package. [2]
The tab is located 45° from pin 1, which is typically the emitter. The typical TO-5 package has a base diameter of 8.9 mm (0.35 in), a cap diameter of 8.1 mm (0.32 in), a cap height of 6.3 mm (0.25 in). [1] The pins are isolated from the package by individual glass-metal seals, or by a single resin potting. Sometimes one pin is connected directly to the metal case.
Several variants of the original TO-5 package have the same cap dimensions but differ in the number and length of the leads (wires). Somewhat incorrectly, TO-5 and TO-39 are often used in manufacturer's literature as synonyms for any package with the cap dimensions of TO-5, regardless of the number of leads, or even for any package with the diameter of TO-5, regardless of the cap height and the number of leads. [3] Compared to TO-5, for the other variants (except TO-33 and TO-42) the minimum length of the leads was shortened from 38.1 mm (1.50 in) to 12.7 mm (0.50 in) which is sufficient for through-hole technology and leads to a cost reduction, whereas the longer leads were needed for point-to-point construction. Lead lengths of 25.4 mm (1.00 in) and 19.05 mm (0.750 in) are quite common but were not standardized separately by JEDEC. There are variants with between 2 and 12 leads. The leads are arranged in a circle with a diameter of 5.08 mm (0.200 in) (except TO-96, TO-97, TO-100, TO-101). Before the introduction of dual in-line packages in 1965, integrated circuits were packaged mostly in metal can packages such as the TO-5 variants with more than 3 leads. [4]
The TO-39, TO-9, and TO-16 packages have 3 leads and differ in the shortened leads mentioned above from TO-5. [5] Additionally, the TO-9 and TO-16 packages do not have a tab. [6] The TO-42 package is almost identical to the TO-5 package (including the long leads) but has four stand-offs at the bottom of the base that keep the base about 0.5 mm above the circuit board. [7] Possibly the TO-16 and TO-42 designations were not actually used. [2]
The TO-12 and TO-33 packages have 4 leads. [8] TO-33 has 38.1 mm (1.50 in) leads [9] like TO-5 while TO-12 has 12.7 mm (0.50 in) leads. For transistors, the fourth wire is typically connected to the metal case as a means of electromagnetic shielding for radio frequency applications.
The TO-75 package has 6 leads (at most one of those may be omitted). [10] The minimum angle between two adjacent leads is 60°.
The TO-76 and TO-77 packages have 8 leads (up to three of those may be omitted). [11] The minimum angle between two adjacent leads is 45°. The TO-77 package differs from the TO-76 package only in that the bottom of a TO-77 package can sit directly on a circuit board whereas the TO-76 package requires a distance of up to 1.02 mm (0.040 in) between circuit board and package. [12]
The TO-78, [13] TO-79, [14] TO-80, [15] and TO-99 [16] packages have 8 leads (up to three of those may be omitted). The minimum angle between two adjacent leads is 45°. These packages differ from other variants in the height of the cap. Instead of 6.3 mm (0.25 in) the cap height is only 4.45 mm (0.175 in) for TO-78 / TO-99, 3.81 mm (0.150 in) for TO-79, and 2.41 mm (0.095 in) for TO-80. The TO-78 package differs from the TO-99 package only in that the bottom of a TO-78 package can sit directly on a circuit board whereas the TO-99 package requires a distance of up to 1.02 mm (0.040 in) between circuit board and package.
The TO-74 package has 10 leads (at most one of those may be omitted). [17] The minimum angle between two adjacent leads is 36°.
The TO-96, [18] TO-97, [19] and TO-100 [20] packages have 10 leads (at most one of those may be omitted). The minimum angle between two adjacent leads is 36°. For these packages the diameter of the circle of leads is increased from 5.08 mm (0.200 in) to 5.84 mm (0.230 in). This allows a slightly increased chip area in a cap of unchanged diameter. TO-96 has the standard cap height of 6.3 mm (0.25 in), while TO-100 and TO-97 have reduced cap heights of 4.45 mm (0.175 in) (like TO-78) and 3.81 mm (0.150 in) (like TO-79), respectively.
The TO-73 package has 12 leads (at most one of those may be omitted). [21] The minimum angle between two adjacent leads is 30°.
The TO-101 package has 12 leads (at most one of those may be omitted). [22] The minimum angle between two adjacent leads is 30°. For this package the diameter of the circle of leads is increased from 5.08 mm (0.200 in) to 5.84 mm (0.230 in). This allows a slightly increased chip area in a cap of unchanged diameter. TO-101 has a reduced cap height of 4.45 mm (0.175 in) (like TO-78).
TO-205 is intended to replace previous definitions of packages with leads arranged in a circle with a diameter of 5.08 mm (0.200 in). [23] [24] The different outlines are now defined as variants of TO-205: TO-5 is renamed to TO-205-AA, TO-12 to TO-205-AB, TO-33 to TO-205-AC, TO-39 to TO-205-AD. A new package with 3 leads and a cap height of 4.32 mm (0.170 in) (similar to TO-78 / TO-99) is added as TO-205-AF.
Standards organization | Standard | Designation for | ||||
---|---|---|---|---|---|---|
TO-5 | TO-12 | TO-33 | TO-39 | TO-77 | ||
JEDEC | JEP95 [24] | TO-205-AA | TO-205-AB | TO-205-AC | TO-205-AD | — |
IEC | IEC 60191 [a] [25] | C4/B4A | C4/B6C | C4/B6A | C4/B4C | C4/B7C |
DIN | DIN 41873 [26] [25] | 5A3 | 5C4 | 5C3 | 5C8 | |
EIAJ / JEITA | ED-7500A [a] [27] | TC5/TB-5A | TC5/TB-14C | TC5/TB-14A | TC5/TB-5C | TC5/TB-15C |
British Standards | BS 3934 [a] [28] [25] | SO-3/SB3-3A | SO-3/SB4-1B | SO-3/SB3-3B | SO-3/SB8-1B | |
Gosstandart | GOST 18472—88 [29] | — | KT-2-12 [b] | — | KT-2-7 [c] | — |
Rosstandart | GOST R 57439 [30] | |||||
Kombinat Mikroelektronik Erfurt | TGL 11811 [31] | — | — | — | B3/15-3a | — |
TGL 26713/07 [31] | — | — | — | F1BC3 | — |
In electronics, TO-5 is a designation for a standardized metal semiconductor package used for transistors and some integrated circuits. The TO element stands for "transistor outline" and refers to a series of technical drawings produced by JEDEC. [1] The first commercial silicon transistors, the 2N696 and 2N697 from Fairchild Semiconductor, came in a TO-5 package. [2]
The tab is located 45° from pin 1, which is typically the emitter. The typical TO-5 package has a base diameter of 8.9 mm (0.35 in), a cap diameter of 8.1 mm (0.32 in), a cap height of 6.3 mm (0.25 in). [1] The pins are isolated from the package by individual glass-metal seals, or by a single resin potting. Sometimes one pin is connected directly to the metal case.
Several variants of the original TO-5 package have the same cap dimensions but differ in the number and length of the leads (wires). Somewhat incorrectly, TO-5 and TO-39 are often used in manufacturer's literature as synonyms for any package with the cap dimensions of TO-5, regardless of the number of leads, or even for any package with the diameter of TO-5, regardless of the cap height and the number of leads. [3] Compared to TO-5, for the other variants (except TO-33 and TO-42) the minimum length of the leads was shortened from 38.1 mm (1.50 in) to 12.7 mm (0.50 in) which is sufficient for through-hole technology and leads to a cost reduction, whereas the longer leads were needed for point-to-point construction. Lead lengths of 25.4 mm (1.00 in) and 19.05 mm (0.750 in) are quite common but were not standardized separately by JEDEC. There are variants with between 2 and 12 leads. The leads are arranged in a circle with a diameter of 5.08 mm (0.200 in) (except TO-96, TO-97, TO-100, TO-101). Before the introduction of dual in-line packages in 1965, integrated circuits were packaged mostly in metal can packages such as the TO-5 variants with more than 3 leads. [4]
The TO-39, TO-9, and TO-16 packages have 3 leads and differ in the shortened leads mentioned above from TO-5. [5] Additionally, the TO-9 and TO-16 packages do not have a tab. [6] The TO-42 package is almost identical to the TO-5 package (including the long leads) but has four stand-offs at the bottom of the base that keep the base about 0.5 mm above the circuit board. [7] Possibly the TO-16 and TO-42 designations were not actually used. [2]
The TO-12 and TO-33 packages have 4 leads. [8] TO-33 has 38.1 mm (1.50 in) leads [9] like TO-5 while TO-12 has 12.7 mm (0.50 in) leads. For transistors, the fourth wire is typically connected to the metal case as a means of electromagnetic shielding for radio frequency applications.
The TO-75 package has 6 leads (at most one of those may be omitted). [10] The minimum angle between two adjacent leads is 60°.
The TO-76 and TO-77 packages have 8 leads (up to three of those may be omitted). [11] The minimum angle between two adjacent leads is 45°. The TO-77 package differs from the TO-76 package only in that the bottom of a TO-77 package can sit directly on a circuit board whereas the TO-76 package requires a distance of up to 1.02 mm (0.040 in) between circuit board and package. [12]
The TO-78, [13] TO-79, [14] TO-80, [15] and TO-99 [16] packages have 8 leads (up to three of those may be omitted). The minimum angle between two adjacent leads is 45°. These packages differ from other variants in the height of the cap. Instead of 6.3 mm (0.25 in) the cap height is only 4.45 mm (0.175 in) for TO-78 / TO-99, 3.81 mm (0.150 in) for TO-79, and 2.41 mm (0.095 in) for TO-80. The TO-78 package differs from the TO-99 package only in that the bottom of a TO-78 package can sit directly on a circuit board whereas the TO-99 package requires a distance of up to 1.02 mm (0.040 in) between circuit board and package.
The TO-74 package has 10 leads (at most one of those may be omitted). [17] The minimum angle between two adjacent leads is 36°.
The TO-96, [18] TO-97, [19] and TO-100 [20] packages have 10 leads (at most one of those may be omitted). The minimum angle between two adjacent leads is 36°. For these packages the diameter of the circle of leads is increased from 5.08 mm (0.200 in) to 5.84 mm (0.230 in). This allows a slightly increased chip area in a cap of unchanged diameter. TO-96 has the standard cap height of 6.3 mm (0.25 in), while TO-100 and TO-97 have reduced cap heights of 4.45 mm (0.175 in) (like TO-78) and 3.81 mm (0.150 in) (like TO-79), respectively.
The TO-73 package has 12 leads (at most one of those may be omitted). [21] The minimum angle between two adjacent leads is 30°.
The TO-101 package has 12 leads (at most one of those may be omitted). [22] The minimum angle between two adjacent leads is 30°. For this package the diameter of the circle of leads is increased from 5.08 mm (0.200 in) to 5.84 mm (0.230 in). This allows a slightly increased chip area in a cap of unchanged diameter. TO-101 has a reduced cap height of 4.45 mm (0.175 in) (like TO-78).
TO-205 is intended to replace previous definitions of packages with leads arranged in a circle with a diameter of 5.08 mm (0.200 in). [23] [24] The different outlines are now defined as variants of TO-205: TO-5 is renamed to TO-205-AA, TO-12 to TO-205-AB, TO-33 to TO-205-AC, TO-39 to TO-205-AD. A new package with 3 leads and a cap height of 4.32 mm (0.170 in) (similar to TO-78 / TO-99) is added as TO-205-AF.
Standards organization | Standard | Designation for | ||||
---|---|---|---|---|---|---|
TO-5 | TO-12 | TO-33 | TO-39 | TO-77 | ||
JEDEC | JEP95 [24] | TO-205-AA | TO-205-AB | TO-205-AC | TO-205-AD | — |
IEC | IEC 60191 [a] [25] | C4/B4A | C4/B6C | C4/B6A | C4/B4C | C4/B7C |
DIN | DIN 41873 [26] [25] | 5A3 | 5C4 | 5C3 | 5C8 | |
EIAJ / JEITA | ED-7500A [a] [27] | TC5/TB-5A | TC5/TB-14C | TC5/TB-14A | TC5/TB-5C | TC5/TB-15C |
British Standards | BS 3934 [a] [28] [25] | SO-3/SB3-3A | SO-3/SB4-1B | SO-3/SB3-3B | SO-3/SB8-1B | |
Gosstandart | GOST 18472—88 [29] | — | KT-2-12 [b] | — | KT-2-7 [c] | — |
Rosstandart | GOST R 57439 [30] | |||||
Kombinat Mikroelektronik Erfurt | TGL 11811 [31] | — | — | — | B3/15-3a | — |
TGL 26713/07 [31] | — | — | — | F1BC3 | — |