The RKM code, [1] also referred to as "letter and numeral code for resistance and capacitance values and tolerances", [1] "letter and digit code for resistance and capacitance values and tolerances", [2] [3] or informally as "R notation" [4] [5] [6] [7] [8] [9] is a notation to specify resistor and capacitor values defined in the international standard IEC 60062 (formerly IEC 62) since 1952. Other standards including DIN 40825 (1973), BS 1852 (1975), [10] IS 8186 (1976), and EN 60062 (1993) have also accepted it. The updated IEC 60062:2016, [1] amended in 2019, comprises the most recent release of the standard.
Originally meant also as part marking code, this shorthand notation is widely used in electrical engineering to denote the values of resistors and capacitors in circuit diagrams and in the production of electronic circuits (for example in bills of material and in silk screens). This method avoids overlooking the decimal separator, which may not be rendered reliably on components or when duplicating documents.
The standards also define a color code for fixed resistors.
R47 | 0.47 ohm |
4R7 | 4.7 ohm |
470R | 470 ohm |
4K7 | 4.7 kilohm |
47K | 47 kilohm |
47K3 | 47.3 kilohm |
470K | 470 kilohm |
4M7 | 4.7 megohm |
For brevity, the notation omits to always specify the unit ( ohm or farad) explicitly and instead relies on implicit knowledge raised from the usage of specific letters either only for resistors or for capacitors, [nb 1] the case used (uppercase letters are typically used for resistors, lowercase letters for capacitors), [nb 2] a part's appearance, and the context.
The notation also avoids using a decimal separator and replaces it by a letter associated with the prefix symbol for the particular value. [nb 3]
This is not only for brevity (for example when printed on the part or PCB), but also to circumvent the problem that decimal separators tend to "disappear" when photocopying printed circuit diagrams.
Another advantage is the easier sortability of values which helps to optimize the bill of materials by combining similar part values to improve maintainability and reduce costs. [nb 4]
The code letters are loosely related to the corresponding SI prefix, but there are several exceptions, where the capitalization differs or alternative letters are used.
For example, 8K2
indicates a resistor value of 8.2 kΩ. Additional zeros imply tighter tolerance, for example 15M0
.
When the value can be expressed without the need for a prefix, an "R" is used instead of the decimal separator. For example, 1R2
indicates 1.2 Ω, and 18R
indicates 18 Ω.
Code letter | SI prefix | Multiplier [12] | |||
---|---|---|---|---|---|
Resistance [ Ω] | Capacitance [ F] | Name | Symbol | Base 10 | Value |
— | p (P [nb 2]) | pico | p | × 10−12 | × 0.000000000001 |
— | n (N [nb 2]) | nano | n | × 10−9 | × 0.000000001 |
— | µ (u, U [nb 2]) | micro | µ | × 10−6 | × 0.000001 |
L | m (M [nb 1] [nb 2]) | milli | m | × 10−3 | × 0.001 |
R (E [nb 5]) | F | — | — | × 100 | × 1 |
K (k [nb 6]) | — | kilo | k | × 103 | × 1000 |
M [nb 1] | — | mega | M | × 106 | × 1000000 |
G | — | giga | G | × 109 | × 1000000000 |
T | — | tera | T | × 1012 | × 1000000000000 |
For resistances, the standard dictates the use of the uppercase letters L
(for 10−3), R
(for 100 = 1), K
(for 103), M
(for 106), and G
(for 109) to be used instead of the decimal point.
The usage of the letter R
instead of the SI unit symbol Ω for ohms stems from the fact that the Greek letter Ω is absent from most older
character encodings (though it is present in the now-ubiquitous
Unicode) and therefore is sometimes impossible to reproduce, in particular in some CAD/CAM environments. The letter R
was chosen because visually it loosely resembles the Ω glyph, and also because it works nicely as a
mnemonic for resistance in many languages.[
citation needed]
The letters G
and T
weren't part of the first issue of the standard, which pre-dates the introduction of the
SI system (hence the name "RKM code"), but were added after the adoption of the corresponding SI prefixes.
The introduction of the letter L
in more recent issues of the standard (instead of an
SI prefix m
for
milli) is justified to maintain the rule of only using uppercase letters for resistances (the otherwise resulting M
was already in use for
mega).
Similar, the standard prescribes the following lowercase letters for capacitances to be used instead of the decimal point: p
(for 10−12), n
(for 10−9), µ
(for 10−6), m
(for 10−3), but uppercase F
(for 100 = 1) for
farad.
The letters p
and n
weren't part of the first issue of the standard, but were added after the adoption of the corresponding SI prefixes.
In cases where the Greek letter µ
is not available, the standard allows it to be replaced by u
(or U
, when only uppercase letters are available). This usage of u
instead of µ
is also in line with
ISO 2955 (1974,
[13] 1983
[14]),
DIN 66030 (Vornorm 1973;
[15] 1980,
[16]
[17] 2002
[18]),
BS 6430 (1983) and
Health Level 7 (HL7),
[19] which allow the prefix μ
to be substituted by the letter u
(or U
) in circumstances in which only the
Latin alphabet is available.
Several manufacturers of resistors utilize the RKM code as part of the components' manufacturer's part numbers (MPNs). [20] [21]
Though non-standard, some manufacturers also use the RKM code to mark inductors with "R" indicating the decimal point in microhenry (e.g. 4R7 for 4.7 μH). [22] [23]
A similar non-standard notation using the unit symbol instead of a decimal separator is sometimes used to indicate voltages (i.e. 0V8 for 0.8 V, 1V8 for 1.8 V, 3V3 for 3.3 V or 5V0 for 5.0 V [24] [25] [26]) in contexts where a decimal separator would be inappropriate (e.g. in signal or pin names, in file names, or in labels or subscripts).
Letter code for resistance and capacitance tolerances:
Code letter | Tolerance | |||
---|---|---|---|---|
Resistance | Capacitance | Relative | Absolute | |
Symmetrical | Asymmetrical | C <10 pF only | ||
A | A | variable (±0.05%) | variable | variable |
B | B | ±0.1% | — | |
C | C | ±0.25% | — | ±0.25 pF |
D | D | ±0.5% | — | ±0.5 pF |
E | ±0.005% | — | — | |
F | F | ±1.0% | — | ±1.0 pF |
G | G | ±2.0% | — | ±2.0 pF |
H | H | ±3.0% | — | — |
J | J | ±5.0% | — | — |
K | K | ±10% | — | — |
L | ±0.01% | — | — | |
M | M | ±20% | — | — |
N | ±30% | — | — | |
P | ±0.02% | — | — | |
Q | — | −10/+30% | — | |
S | — | −20/+50% | — | |
T | — | −10/+50% | — | |
W | ±0.05% | — | — | |
Z | — | −20/+80% | — |
Before the introduction of the RKM code, some of the letters for symmetrical tolerances (viz. G, J, K, M) were already used in US military contexts following the American War Standard (AWS) and Joint Army-Navy Specifications (JAN) since the mid-1940s. [27]
Letter codes for the temperature coefficient of resistance (TCR):
Code letter | ppm/K |
---|---|
K | 1 |
L | 2 |
M | 5 |
N | 10 |
P | 15 |
Q | 25 |
R | 50 |
S | 100 |
U | 250 |
Z | other |
Example: J8 = August 2017 (or August 1997)
Some manufacturers also used the production date code as a stand-alone code to indicate the production date of integrated circuits. [33]
Some manufacturers specify a three-character date code with a two-digit week number following the year letter. [34]
IEC 60062 also specifies a four-character year/week code.
Example: 78 = August 2017
IEC 60062 also specifies a four-character year/week code.
IEC 60062 also specifies a single-character four-year cycle year/month code. [nb 9]
Year | Month | Letter |
---|---|---|
1993 1997 2001 2005 2009 2013 2017 2021 |
1 | A |
2 | B | |
3 | C | |
4 | D | |
5 | E | |
6 | F | |
7 | G | |
8 | H | |
9 | J | |
10 | K | |
11 | L | |
12 | M |
Year | Month | Letter |
---|---|---|
1994 1998 2002 2006 2010 2014 2018 2022 |
1 | N |
2 | P | |
3 | Q | |
4 | R | |
5 | S | |
6 | T | |
7 | U | |
8 | V | |
9 | W | |
10 | X | |
11 | Y | |
12 | Z |
Year | Month | Letter |
---|---|---|
1995 1999 2003 2007 2011 2015 2019 2023 |
1 | a |
2 | b | |
3 | c | |
4 | d | |
5 | e | |
6 | f | |
7 | g | |
8 | h | |
9 | j | |
10 | k | |
11 | l | |
12 | m |
Year | Month | Letter |
---|---|---|
1996 2000 2004 2008 2012 2016 2020 2024 |
1 | n |
2 | p | |
3 | q | |
4 | r | |
5 | s | |
6 | t | |
7 | u | |
8 | v | |
9 | w | |
10 | x | |
11 | y | |
12 | z |
For resistances following the ( E48 or) E96 series of preferred values, the former EIA-96 as well as IEC 60062:2016 define a special three-character marking code for resistors to be used on small parts. The code consists of two digits denoting one of the "positions" in the series of E96 values followed by a letter indicating the multiplier.
For capacitances following the ( E3, E6, E12 or) E24 series of preferred values, the former ANSI/EIA-198-D:1991, ANSI/EIA-198-1-E:1998 and ANSI/EIA-198-1-F:2002 as well as the amendment IEC 60062:2016/AMD1:2019 to IEC 60062 define a special two-character marking code for capacitors for very small parts which leave no room to print any longer codes onto them. The code consists of an uppercase letter denoting the two significant digits of the value followed by a digit indicating the multiplier. The EIA standard also defines a number of lowercase letters to specify a number of values not found in E24. [35]
M
was an exception to the rule that all different letters are supposed to be used for resistances and capacitances. Today, a lowercase letter m
should be used for capacitances whenever possible to avoid confusion.
F
).
.
and ,
), and these characters are also used as
thousands separators in some areas, avoiding to use decimal separators also has the advantage of not risking to become ambiguous in an international context.
E
instead of R
is not standardized in IEC 60062, but nevertheless sometimes seen in practice. It stems from the fact, that R
is used in symbolic names for resistors as well, and it is also used in a similar fashion but with incompatible meaning in other part marking codes. It may therefore cause confusion in some contexts. Visually, the letter E
loosely resembles a small Greek letter
omega (ω) turned sideways. Historically (i.e. in pre-
WWII documents), before
ohms were denoted using the uppercase Greek omega (Ω), a small omega (ω) was sometimes used for this purpose as well, as in 56ω for 56 Ω. However, the letter E
is conflictive with the similar looking but incompatible
E notation in engineering, and it may therefore cause considerable confusion as well.
K
only, however, a lowercase k
is nevertheless often seen in
schematics and
bills of materials probably because the corresponding
SI prefix is defined as a lowercase k
.
G
(6
), I
(J
, 1
), O
(0
, Q
, D
), Q
(O
, D
, 0
), Y
, Z
(2
) are not used as their glyphs look similar to other letters and digits.
A
, J
, M
) the code for the most part uses digits. Since letter O
is easily confused with digit 0
, the code is arranged so that the letter O
is used for October, the tenth month, rather than for January.
I
/i
and O
/o
are not used as their glyphs look similar to other letters and digits.
Part marking: XXX=Inductance value in uH, R= decimal point. If no R is present then last character equals number of zeros
These are the inductances expressed in a unit of microhenry (uH). The first two digits indicate significant figures and the third digit a multiplier. When there is an "R", it indicates a decimal point, and all numbers are significant figures.
The RKM code, [1] also referred to as "letter and numeral code for resistance and capacitance values and tolerances", [1] "letter and digit code for resistance and capacitance values and tolerances", [2] [3] or informally as "R notation" [4] [5] [6] [7] [8] [9] is a notation to specify resistor and capacitor values defined in the international standard IEC 60062 (formerly IEC 62) since 1952. Other standards including DIN 40825 (1973), BS 1852 (1975), [10] IS 8186 (1976), and EN 60062 (1993) have also accepted it. The updated IEC 60062:2016, [1] amended in 2019, comprises the most recent release of the standard.
Originally meant also as part marking code, this shorthand notation is widely used in electrical engineering to denote the values of resistors and capacitors in circuit diagrams and in the production of electronic circuits (for example in bills of material and in silk screens). This method avoids overlooking the decimal separator, which may not be rendered reliably on components or when duplicating documents.
The standards also define a color code for fixed resistors.
R47 | 0.47 ohm |
4R7 | 4.7 ohm |
470R | 470 ohm |
4K7 | 4.7 kilohm |
47K | 47 kilohm |
47K3 | 47.3 kilohm |
470K | 470 kilohm |
4M7 | 4.7 megohm |
For brevity, the notation omits to always specify the unit ( ohm or farad) explicitly and instead relies on implicit knowledge raised from the usage of specific letters either only for resistors or for capacitors, [nb 1] the case used (uppercase letters are typically used for resistors, lowercase letters for capacitors), [nb 2] a part's appearance, and the context.
The notation also avoids using a decimal separator and replaces it by a letter associated with the prefix symbol for the particular value. [nb 3]
This is not only for brevity (for example when printed on the part or PCB), but also to circumvent the problem that decimal separators tend to "disappear" when photocopying printed circuit diagrams.
Another advantage is the easier sortability of values which helps to optimize the bill of materials by combining similar part values to improve maintainability and reduce costs. [nb 4]
The code letters are loosely related to the corresponding SI prefix, but there are several exceptions, where the capitalization differs or alternative letters are used.
For example, 8K2
indicates a resistor value of 8.2 kΩ. Additional zeros imply tighter tolerance, for example 15M0
.
When the value can be expressed without the need for a prefix, an "R" is used instead of the decimal separator. For example, 1R2
indicates 1.2 Ω, and 18R
indicates 18 Ω.
Code letter | SI prefix | Multiplier [12] | |||
---|---|---|---|---|---|
Resistance [ Ω] | Capacitance [ F] | Name | Symbol | Base 10 | Value |
— | p (P [nb 2]) | pico | p | × 10−12 | × 0.000000000001 |
— | n (N [nb 2]) | nano | n | × 10−9 | × 0.000000001 |
— | µ (u, U [nb 2]) | micro | µ | × 10−6 | × 0.000001 |
L | m (M [nb 1] [nb 2]) | milli | m | × 10−3 | × 0.001 |
R (E [nb 5]) | F | — | — | × 100 | × 1 |
K (k [nb 6]) | — | kilo | k | × 103 | × 1000 |
M [nb 1] | — | mega | M | × 106 | × 1000000 |
G | — | giga | G | × 109 | × 1000000000 |
T | — | tera | T | × 1012 | × 1000000000000 |
For resistances, the standard dictates the use of the uppercase letters L
(for 10−3), R
(for 100 = 1), K
(for 103), M
(for 106), and G
(for 109) to be used instead of the decimal point.
The usage of the letter R
instead of the SI unit symbol Ω for ohms stems from the fact that the Greek letter Ω is absent from most older
character encodings (though it is present in the now-ubiquitous
Unicode) and therefore is sometimes impossible to reproduce, in particular in some CAD/CAM environments. The letter R
was chosen because visually it loosely resembles the Ω glyph, and also because it works nicely as a
mnemonic for resistance in many languages.[
citation needed]
The letters G
and T
weren't part of the first issue of the standard, which pre-dates the introduction of the
SI system (hence the name "RKM code"), but were added after the adoption of the corresponding SI prefixes.
The introduction of the letter L
in more recent issues of the standard (instead of an
SI prefix m
for
milli) is justified to maintain the rule of only using uppercase letters for resistances (the otherwise resulting M
was already in use for
mega).
Similar, the standard prescribes the following lowercase letters for capacitances to be used instead of the decimal point: p
(for 10−12), n
(for 10−9), µ
(for 10−6), m
(for 10−3), but uppercase F
(for 100 = 1) for
farad.
The letters p
and n
weren't part of the first issue of the standard, but were added after the adoption of the corresponding SI prefixes.
In cases where the Greek letter µ
is not available, the standard allows it to be replaced by u
(or U
, when only uppercase letters are available). This usage of u
instead of µ
is also in line with
ISO 2955 (1974,
[13] 1983
[14]),
DIN 66030 (Vornorm 1973;
[15] 1980,
[16]
[17] 2002
[18]),
BS 6430 (1983) and
Health Level 7 (HL7),
[19] which allow the prefix μ
to be substituted by the letter u
(or U
) in circumstances in which only the
Latin alphabet is available.
Several manufacturers of resistors utilize the RKM code as part of the components' manufacturer's part numbers (MPNs). [20] [21]
Though non-standard, some manufacturers also use the RKM code to mark inductors with "R" indicating the decimal point in microhenry (e.g. 4R7 for 4.7 μH). [22] [23]
A similar non-standard notation using the unit symbol instead of a decimal separator is sometimes used to indicate voltages (i.e. 0V8 for 0.8 V, 1V8 for 1.8 V, 3V3 for 3.3 V or 5V0 for 5.0 V [24] [25] [26]) in contexts where a decimal separator would be inappropriate (e.g. in signal or pin names, in file names, or in labels or subscripts).
Letter code for resistance and capacitance tolerances:
Code letter | Tolerance | |||
---|---|---|---|---|
Resistance | Capacitance | Relative | Absolute | |
Symmetrical | Asymmetrical | C <10 pF only | ||
A | A | variable (±0.05%) | variable | variable |
B | B | ±0.1% | — | |
C | C | ±0.25% | — | ±0.25 pF |
D | D | ±0.5% | — | ±0.5 pF |
E | ±0.005% | — | — | |
F | F | ±1.0% | — | ±1.0 pF |
G | G | ±2.0% | — | ±2.0 pF |
H | H | ±3.0% | — | — |
J | J | ±5.0% | — | — |
K | K | ±10% | — | — |
L | ±0.01% | — | — | |
M | M | ±20% | — | — |
N | ±30% | — | — | |
P | ±0.02% | — | — | |
Q | — | −10/+30% | — | |
S | — | −20/+50% | — | |
T | — | −10/+50% | — | |
W | ±0.05% | — | — | |
Z | — | −20/+80% | — |
Before the introduction of the RKM code, some of the letters for symmetrical tolerances (viz. G, J, K, M) were already used in US military contexts following the American War Standard (AWS) and Joint Army-Navy Specifications (JAN) since the mid-1940s. [27]
Letter codes for the temperature coefficient of resistance (TCR):
Code letter | ppm/K |
---|---|
K | 1 |
L | 2 |
M | 5 |
N | 10 |
P | 15 |
Q | 25 |
R | 50 |
S | 100 |
U | 250 |
Z | other |
Example: J8 = August 2017 (or August 1997)
Some manufacturers also used the production date code as a stand-alone code to indicate the production date of integrated circuits. [33]
Some manufacturers specify a three-character date code with a two-digit week number following the year letter. [34]
IEC 60062 also specifies a four-character year/week code.
Example: 78 = August 2017
IEC 60062 also specifies a four-character year/week code.
IEC 60062 also specifies a single-character four-year cycle year/month code. [nb 9]
Year | Month | Letter |
---|---|---|
1993 1997 2001 2005 2009 2013 2017 2021 |
1 | A |
2 | B | |
3 | C | |
4 | D | |
5 | E | |
6 | F | |
7 | G | |
8 | H | |
9 | J | |
10 | K | |
11 | L | |
12 | M |
Year | Month | Letter |
---|---|---|
1994 1998 2002 2006 2010 2014 2018 2022 |
1 | N |
2 | P | |
3 | Q | |
4 | R | |
5 | S | |
6 | T | |
7 | U | |
8 | V | |
9 | W | |
10 | X | |
11 | Y | |
12 | Z |
Year | Month | Letter |
---|---|---|
1995 1999 2003 2007 2011 2015 2019 2023 |
1 | a |
2 | b | |
3 | c | |
4 | d | |
5 | e | |
6 | f | |
7 | g | |
8 | h | |
9 | j | |
10 | k | |
11 | l | |
12 | m |
Year | Month | Letter |
---|---|---|
1996 2000 2004 2008 2012 2016 2020 2024 |
1 | n |
2 | p | |
3 | q | |
4 | r | |
5 | s | |
6 | t | |
7 | u | |
8 | v | |
9 | w | |
10 | x | |
11 | y | |
12 | z |
For resistances following the ( E48 or) E96 series of preferred values, the former EIA-96 as well as IEC 60062:2016 define a special three-character marking code for resistors to be used on small parts. The code consists of two digits denoting one of the "positions" in the series of E96 values followed by a letter indicating the multiplier.
For capacitances following the ( E3, E6, E12 or) E24 series of preferred values, the former ANSI/EIA-198-D:1991, ANSI/EIA-198-1-E:1998 and ANSI/EIA-198-1-F:2002 as well as the amendment IEC 60062:2016/AMD1:2019 to IEC 60062 define a special two-character marking code for capacitors for very small parts which leave no room to print any longer codes onto them. The code consists of an uppercase letter denoting the two significant digits of the value followed by a digit indicating the multiplier. The EIA standard also defines a number of lowercase letters to specify a number of values not found in E24. [35]
M
was an exception to the rule that all different letters are supposed to be used for resistances and capacitances. Today, a lowercase letter m
should be used for capacitances whenever possible to avoid confusion.
F
).
.
and ,
), and these characters are also used as
thousands separators in some areas, avoiding to use decimal separators also has the advantage of not risking to become ambiguous in an international context.
E
instead of R
is not standardized in IEC 60062, but nevertheless sometimes seen in practice. It stems from the fact, that R
is used in symbolic names for resistors as well, and it is also used in a similar fashion but with incompatible meaning in other part marking codes. It may therefore cause confusion in some contexts. Visually, the letter E
loosely resembles a small Greek letter
omega (ω) turned sideways. Historically (i.e. in pre-
WWII documents), before
ohms were denoted using the uppercase Greek omega (Ω), a small omega (ω) was sometimes used for this purpose as well, as in 56ω for 56 Ω. However, the letter E
is conflictive with the similar looking but incompatible
E notation in engineering, and it may therefore cause considerable confusion as well.
K
only, however, a lowercase k
is nevertheless often seen in
schematics and
bills of materials probably because the corresponding
SI prefix is defined as a lowercase k
.
G
(6
), I
(J
, 1
), O
(0
, Q
, D
), Q
(O
, D
, 0
), Y
, Z
(2
) are not used as their glyphs look similar to other letters and digits.
A
, J
, M
) the code for the most part uses digits. Since letter O
is easily confused with digit 0
, the code is arranged so that the letter O
is used for October, the tenth month, rather than for January.
I
/i
and O
/o
are not used as their glyphs look similar to other letters and digits.
Part marking: XXX=Inductance value in uH, R= decimal point. If no R is present then last character equals number of zeros
These are the inductances expressed in a unit of microhenry (uH). The first two digits indicate significant figures and the third digit a multiplier. When there is an "R", it indicates a decimal point, and all numbers are significant figures.